topic Re: convert 5 number manually to array in LabVIEW

convert 5 number manually to array

Himmel — Fri, 08 Jul 2016 10:50:41 GMT

Hi every one ,

I want to press 5 number by slider manually to array .

can you help me , how i do it .

thanks

Re: convert 5 number manually to array

GerdW — Fri, 08 Jul 2016 10:56:02 GMT

Hi Himmel,

use the BuildArray function to build an array…

You know this is pretty basic LabVIEW stuff explained in the beginner tutorials?

Re: convert 5 number manually to array

PazhanivelVenkatt — Fri, 08 Jul 2016 10:57:06 GMT

can you provide more details

Re: convert 5 number manually to array

Himmel — Fri, 08 Jul 2016 11:01:41 GMT

I know but every time I want a number and I want the numbers press in each element in array .

Re: convert 5 number manually to array

Himmel — Fri, 08 Jul 2016 11:09:33 GMT

I want to convert 5 different numbers to array . but I have just 1 control (slider ) .

Re: convert 5 number manually to array

GerdW — Fri, 08 Jul 2016 12:04:44 GMT

Hi Himmel,

and how do you want to put 5 values into an array using just one slider control?

Re: convert 5 number manually to array

Himmel — Fri, 08 Jul 2016 12:41:18 GMT

and start my problem from hier . slider simulates as a Sensor . I want sensor sends the value as a number and after 5 number are sent . they are creat as a array . I want it by for loop . but I can`t .

Re: convert 5 number manually to array

Norbert_B — Fri, 08 Jul 2016 12:56:23 GMT

Loop is already a good start.

Next key words you should look up:

- Shiftregister

- Build Array function

Norbert

Re: convert 5 number manually to array

PazhanivelVenkatt — Fri, 08 Jul 2016 13:00:04 GMT

Try to post your original code which you are trying?

Hope your Requirment looks simple but its not providing clear understanding.

Re: convert 5 number manually to array

Himmel — Fri, 08 Jul 2016 13:28:47 GMT

this is my project . I marked the PART, that i can`t solve.

Re: convert 5 number manually to array

GerdW — Fri, 08 Jul 2016 13:35:50 GMT

Hi Himmel,

you need to use (and understand) shift registers - as mentioned before!

Re: convert 5 number manually to array

PazhanivelVenkatt — Fri, 08 Jul 2016 13:45:24 GMT

You need five different values or same value five times

if five different values and values are generated dynamically place the value generation or aquisition inside for loop which will provide five different values

if same value five times feed same value to all five index in this case you dont need loop

Re: convert 5 number manually to array

crossrulz — Fri, 08 Jul 2016 16:37:21 GMT

Instead of 1 large wait, perhaps you should use a smaller wait inside of your loop. This would better simulate a sensor sending you data. And then you just use the autoindexing tunnel to make your array. So since you want 5 readings in 2 seconds, a 400ms wait should work for you.

Re: convert 5 number manually to array

Himmel — Fri, 08 Jul 2016 18:01:56 GMT

thank you !

I am new by Labview . I have another question . in which Platte I can find DBL als control and Array?

Thanks

Re: convert 5 number manually to array

RavensFan — Fri, 08 Jul 2016 18:04:56 GMT

Those are terminal. You create controls on the front panel. Array container in the array palette. Double in the numeric palette.

These are very basic LabVIEW quesitons. I would recommend looking at the online LabVIEW tutorials
LabVIEW Introduction Course - Three Hours
LabVIEW Introduction Course - Six Hours