Motion Control and Motor Drives

Start a topic

Show: - -

switch relais USB-6341

by on Latest post on by

6 Replies 6395 Views

0 Kudos

6 Replies

7New

Need to connect a PCI-7332 cable to a panel and then to an UMI-7764

by on Latest post on by

7 Replies 5741 Views

0 Kudos

7 Replies

8New

Finding hardware limits without limit switch.

by on Latest post on by

3 Replies 6005 Views

1 Kudo

3 Replies

4New

I need to connect a PCI-7332 cable to a front panel and then to an UMI-7764

by on

0 Replies 5345 Views

0 Kudos

0 Replies

1New

Need to connect a PCI-7332 cable to a panel connector and then to an UMI-7764

by on

0 Replies 5151 Views

0 Kudos

0 Replies

1New

High rate coordinate measurement @ NI-Motion 7344

by on Latest post on by

3 Replies 5338 Views

0 Kudos

3 Replies

4New

shared variable vs. data binding

by on Latest post on by

1 Reply 5097 Views

0 Kudos

1 Reply

2New

Is stepper output from 7344 board truly a sinking output?

by on Latest post on by

8 Replies 5207 Views

4 Kudos

8 Replies

9New

Using LabVIEW for compumotors 6k8 controller (for 8-axes stages)

by on Latest post on by

1 Reply 5007 Views

0 Kudos

1 Reply

2New

PCI/FW-7344 Motion controller either isn't found or when it is, MAX crashes depending on which version of NI-Motion, DAQ and Motion Assitant I use.

by on Latest post on by

6 Replies 5115 Views

0 Kudos

6 Replies

7New

time of reading encoder position

by on Latest post on by

3 Replies 5338 Views

0 Kudos

3 Replies

4New

move stage of a microscope with stepper motor movement

by on

0 Replies 5493 Views

0 Kudos

0 Replies

1New

3 linear actuators and 1 semi rotary actuator position Control-all analogue

by on Latest post on by

9 Replies 6305 Views

0 Kudos

9 Replies

10New

Loading PID Parameter and Reading Back

by on Latest post on by

1 Reply 4742 Views

0 Kudos

1 Reply

2New

Robot project with 6 DOF/ Motor control with LV Softmotion RT mode

by on Latest post on by

1 Reply 5530 Views

0 Kudos

1 Reply

2New

How to measure number of pulses of a position single phase position encoder using cRIO 9012,chasis 9101 and NI9401

by on

0 Replies 5542 Views

0 Kudos

0 Replies

1New

Animatics Smartmotor, Out of Box, Now What.

by on Latest post on by

3 Replies 5419 Views

0 Kudos

3 Replies

4New

Automatic motion control for 6 motors and storing the previous positions

by on Latest post on by

2 Replies 4870 Views

0 Kudos

2 Replies

3New

Micro switch in a SolidWorks to LabView through SoftMotion

by on

0 Replies 5437 Views

0 Kudos

0 Replies

1New

NI board to drive two step motors

by on Latest post on by

3 Replies 4923 Views

0 Kudos

3 Replies

4New

Problem Generating the Analogue Output on PCI-7342

[
1
2
]

by on Latest post on by

18 Replies 6611 Views

0 Kudos

18 Replies

19New

-70163(NIMC_invalidLimitRangeError)

by on Latest post on by

3 Replies 5147 Views

0 Kudos

3 Replies

4New

RT multi-motor motion control in a closed loop system

by on Latest post on by

2 Replies 4856 Views

0 Kudos

2 Replies

3New

Test stand design for high speed brushless dc servo motor efficiency testing

by on Latest post on by

2 Replies 5723 Views

0 Kudos

2 Replies

3New

Question of Requirements for Servo Project (Beginner to Motion Control in NI)

by on Latest post on by

2 Replies 4851 Views

0 Kudos

2 Replies

3New

Umi 7774

[
1
2
3
]

by on Latest post on by

21 Replies 5676 Views

0 Kudos

21 Replies

22New

Backlash Compensation software

by on Latest post on by

3 Replies 5345 Views

0 Kudos

3 Replies

4New

dc motor control with H-Bridge..DAQ

by on Latest post on by

1 Reply 5156 Views

0 Kudos

1 Reply

2New

Response of 7390 motion card is speed slow after initialization by c code

by on

0 Replies 5224 Views

0 Kudos

0 Replies

1New

Motion Control and Motor Drives

EtherCAT communication with CU320/S120 from PXI

NI-7340 limit and home switch indicators always active using NI Max

Connecting a 10-30V 3-wire proximity switch to the UMI-7764

CanOpen with ELMO Motor Torque Mode

STM32F407与LABVIEW通信控制步进电机运动

switch relais USB-6341

Need to connect a PCI-7332 cable to a panel and then to an UMI-7764

Finding hardware limits without limit switch.

I need to connect a PCI-7332 cable to a front panel and then to an UMI-7764

Need to connect a PCI-7332 cable to a panel connector and then to an UMI-7764

High rate coordinate measurement @ NI-Motion 7344

shared variable vs. data binding

Is stepper output from 7344 board truly a sinking output?

Using LabVIEW for compumotors 6k8 controller (for 8-axes stages)

PCI/FW-7344 Motion controller either isn't found or when it is, MAX crashes depending on which version of NI-Motion, DAQ and Motion Assitant I use.

time of reading encoder position

move stage of a microscope with stepper motor movement

3 linear actuators and 1 semi rotary actuator position Control-all analogue

Loading PID Parameter and Reading Back

Robot project with 6 DOF/ Motor control with LV Softmotion RT mode

How to measure number of pulses of a position single phase position encoder using cRIO 9012,chasis 9101 and NI9401

Animatics Smartmotor, Out of Box, Now What.

Automatic motion control for 6 motors and storing the previous positions

Micro switch in a SolidWorks to LabView through SoftMotion

NI board to drive two step motors

Problem Generating the Analogue Output on PCI-7342

-70163(NIMC_invalidLimitRangeError)

RT multi-motor motion control in a closed loop system

Test stand design for high speed brushless dc servo motor efficiency testing

Question of Requirements for Servo Project (Beginner to Motion Control in NI)

Umi 7774

Backlash Compensation software

dc motor control with H-Bridge..DAQ

Response of 7390 motion card is speed slow after initialization by c code

simple straight line motion control with brushless motor and encoder/microswitch