Temperature Control MLC9000+250 west by Ethernet/IP

[Kelbert]

Someone could help me?

I am trying to do the protocol by Ethernet/IP for temperature control west model MLC9000 + BM250 S160 EI

I have a software MLC 9000+ workshop, but I can`t find more information or documents about it.

Best and Regards

Kelbert

[Lucianogob]

Hi,

I'm sending to you some tutorials about TCP/IP using VISA:

https://knowledge.ni.com/KnowledgeArticleDetails?id=kA03q000000x3gXCAQ&l=en-US

https://www.ni.com/en/support/documentation/supplemental/21/command-based-communication-design-patte...

https://www.ni.com/en/support/documentation/supplemental/06/basic-tcp-ip-communication-in-labview.ht...

https://forums.ni.com/t5/Reference-Design-Content/Multi-Client-Server-Application-Design-Pattern-usi...

You can find some examples of TCP/IP clicking in Help>>Find Examples and searching for "tcp".

Best Regards

Luciano Borges

National Instruments Brazil

Message Edited by Lucianogob on 04-15-2009 10:08 AM

[Kelbert]

Hi luciano,

I can't find any commands to send and get's answer for this instrument control, I don't have documentation about the protocol that I need for the Instrument control by Ethernet/IP.

I would like that somebody to have a documentation of the protocol of this or where I can research this.

Thank you

Kelbert

[Lucianogob]

Hi Kelbert,

I'm sending to you a link that talk about Ethernet/IP in LabVIEW.

In this link you can find another link to download the Ethernet/IP Driver and VIs. When you install it, it comes with a great documentation about how to use the Ethernet/IP.

https://www.ni.com/en/shop/seamlessly-connect-to-third-party-devices-and-supervisory-system.html

Let me know if you have any question.

Regards.

Luciano Borges

National Instruments

[Kelbert · Accepted solution]

Hi there,

It`s good a link that you send me about Ethernet/IP in LabVIEW.

I have tried 2 ways:

One fo them that I tried with a llb modbus ethernet, but I guess the problem that I don`t know with which is the start adress I need to put it out I don`t have any documentation or imformation of controller that I have here.

The another one I tried with configure modbus I/O server, but there are some probleml.

Check it out the add attachments.

Best Regards

Kelbert

[Lucianogob]

Hi,

This problem usually occur when the address is not right. Don't you have any information about the address for your device?

Regards

Luciano Borges

National Instruments Brazil

[Kelbert]

Hi Luciano,

I don`t any information about it. I have tried to contact the supplier but I didn`t have a success.

About the problem that I posted I guess I can`t use the procotol with Modbus Ethernet because my deveice is Ethernet/IP and I can`t do with the llb Modbus, I think so.

Best Regards

Kelbert

[Lucianogob]

Te envio dos enlaces.

Uno es una introdución al Modbus y el otro tiene una library de Modbus para el LabVIEW:

https://www.ni.com/en/shop/labview/introduction-to-modbus-using-labview.html

https://forums.ni.com/t5/Reference-Design-Content/LabVIEW-Modbus-API/ta-p/3524019

Cordiales Saludos

Luciano Borges

National Instruments Brazil

[Kelbert]

I have tried to contact the Technical Support about the Temperature Control of west, but  they don`t have information about Ethernet/IP protocol.

I decided to change the Ethernet/IP to Modbus RTU, and I have already done without problem.

Thank`s for help!

Kelbert