Home Community Idea Exchange LabVIEW Real-Time Ideas : New Ideas

LabVIEW Real-Time Idea Exchange

Community Browser
Top Authors
View All
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
Post an idea
14 Kudos
PJM_Labview

Smart switching to main application instance.

Status: New Submitted by Active Participant on 11-21-2009 02:01 PM 6 Comment

I do not know about most people use cases with RT system, but I have the reflex to click the run arrow to test all my VIs. When I am on site and I do have access to the hardware, everything is rosy. But, when I do not have access to the hardware, and depending on the system complexity, I now have to wait up to over a minutes before I can resume working. It would be nice if somehow once I realized my mistake I could notified LabVIEW (right away) to run my VI in the main application instance instead of attempting to deploy it on the missing target.

Alternatively, once I made the mistake once, LabVIEW could automatically run the VI in the main application instance.

I do not know what is the best approach to fix this, but I know that I am very annoyed every time I make that mistake.

50 Kudos
DanielRoth

"Reentrant VI Debbugging" Support for LV-Realtime

Status: New Submitted by Member on 11-06-2009 08:15 AM 4 Comment
It is allmost impossible to find errors in "Reentrant SUBVI's" without the debugging possiblities.
 
 
 
 
4 Kudos
DanielRoth

Getting the BIOS Version programmatically

Status: New Submitted by Member on 11-06-2009 07:14 AM 2 Comment
Need a possiblity to read out the installed BIOS Version to check if the system is updated..
View All (2)
51 Kudos
Hueter

RT target IP and software setting should be available from the target properties from the project window

Status: In Development Submitted by Active Participant on 10-29-2009 11:56 AM 8 Comment

I am often working with a compact RIO and I need to change the IP configuration or the software settings. Currently I have to open up MAX refresh my target list (which can sometime take a minute or two since we have so many targets). Then open up the RT target settings.

 

 

I think the IP address and software settings should be accessible from the project window by right-clicking on the target and selecting properties.

The MAX settings page could be reproduced in the general settings section that all ready has a limited ability to edit the IP.

You could also add a  software category, so you could update the version of RIO or install scan engine.RT Target Properties Window.PNG

Message Edited by Hueter on 10-29-2009 11:58 AM
Message Edited by Hueter on 10-29-2009 11:58 AM
View All (8)
29 Kudos
gsussman

Disable the "Connection to the RT system has been lost" dialog when I select to disconnect from an unresponsive system

Status: In Development Submitted by Active Participant on 10-13-2009 03:45 AM 2 Comment
When I choose to "Stop waiting and disconnect" from an RT system that is unresponsive, suppress the dialog box that fires immediately afterward saying that the connection has been lost.....I already know that, I am the one who asked for the disconnection.
43 Kudos
Sima

Better display for real-time (RT) deployment errors

Status: In Development Submitted by Active Participant on 09-01-2009 10:03 AM 2 Comment

If you get errors when deploying your real-time VI, you have to scroll through a small window and many many lines of messages to find the error that's in bold text... often only to find that it's just the "startup application is missing" error. It would be better to have a separate box where the errors are summarized for you.

Message Edited by Laura F. on 10-09-2009 09:01 AM