Motion Control and Motor Drives

Start a topic

Show: - -

Encoder and DAQ Connections

by on Latest post on by

1 Reply 3026 Views

0 Kudos

1 Reply

2New

What third party drive do I use to connect my umi-7764 to a phytron stepper motor (zss66)

by on Latest post on by

2 Replies 3324 Views

1 Kudo

2 Replies

3New

Motion and Vector Space Question

by on Latest post on by

6 Replies 4414 Views

0 Kudos

6 Replies

7New

What are the 4 analog inputs of my umi-7764 (on the analog input terminal block)

by on Latest post on by

1 Reply 3103 Views

1 Kudo

1 Reply

2New

Does the breakpoint/trigger terminal block of my umi-7764 must be connected ?

by on Latest post on by

1 Reply 2893 Views

1 Kudo

1 Reply

2New

What is the needed analog inputs to UMI 7764

by on Latest post on by

2 Replies 3375 Views

0 Kudos

2 Replies

3New

How do i extend the bandwidth of my system

by on Latest post on by

1 Reply 3222 Views

0 Kudos

1 Reply

2New

How to use an LVDT as an input to a UMI 7764

by on Latest post on by

1 Reply 3030 Views

0 Kudos

1 Reply

2New

How to remove motion device from MAX?

by on Latest post on by

4 Replies 3483 Views

0 Kudos

4 Replies

5New

flexmotion reading from board speed

by on Latest post on by

3 Replies 3611 Views

0 Kudos

3 Replies

4New

How can I plot position,velocity and following error vs time?

by on

0 Replies 3342 Views

0 Kudos

0 Replies

1New

can not read back error description in VB

by on Latest post on by

1 Reply 3067 Views

0 Kudos

1 Reply

2New

implementation of Matlab neuro-fuzzy controller with Flexmotion-6C?

by on Latest post on by

1 Reply 3426 Views

0 Kudos

1 Reply

2New

Is it possible to perfectly synchronize 7 axes using 2 motion controllers 7344?

by on Latest post on by

1 Reply 3053 Views

0 Kudos

1 Reply

2New

I´m having problems with a simple synchronized move

by on Latest post on by

3 Replies 3327 Views

0 Kudos

3 Replies

4New

3-D Models

by on Latest post on by

4 Replies 4214 Views

0 Kudos

4 Replies

5New

How can I get a PWM signal of PXI-7344 by UMI?

by on Latest post on by

1 Reply 3089 Views

1 Kudo

1 Reply

2New

High speed torque control with PCI-7342

by on Latest post on by

5 Replies 3945 Views

0 Kudos

5 Replies

6New

Make sure motor is compatible with drive

by on Latest post on by

1 Reply 3045 Views

0 Kudos

1 Reply

2New

how do i stop a motor from staring at full speed

by on Latest post on by

1 Reply 3014 Views

0 Kudos

1 Reply

2New

Any examples that work with a PCI-6733?

by on Latest post on by

1 Reply 2972 Views

0 Kudos

1 Reply

2New

control two different parameters at the same time

by on Latest post on by

5 Replies 3654 Views

0 Kudos

5 Replies

6New

Stepper Motor Control, oscilator, with pauses

by on Latest post on by

1 Reply 2963 Views

0 Kudos

1 Reply

2New

Error using communicate front panel in Value Motion

by on Latest post on by

2 Replies 3148 Views

0 Kudos

2 Replies

3New

re-initialize the data during running the program

by on Latest post on by

1 Reply 2899 Views

0 Kudos

1 Reply

2New

Master Encoder - Slave Axis Gearing (beginner's question)

by on Latest post on by

1 Reply 3100 Views

0 Kudos

1 Reply

2New

FlexMotion 6.1 Read Buffer is buggy.

by on Latest post on by

3 Replies 3437 Views

0 Kudos

3 Replies

4New

problem on control the bushless motors by motion asistant

by on Latest post on by

3 Replies 3272 Views

0 Kudos

3 Replies

4New

configure ValueMotion board

by on Latest post on by

2 Replies 3212 Views

0 Kudos

2 Replies

3New

I need help with motion control. I am programming in Visual Basic. I will need help with what parts I need to purchase from NI, along with help on the code.

Motion Control and Motor Drives

EtherCAT communication with CU320/S120 from PXI

NI-7340 limit and home switch indicators always active using NI Max

Connecting a 10-30V 3-wire proximity switch to the UMI-7764

CanOpen with ELMO Motor Torque Mode

STM32F407与LABVIEW通信控制步进电机运动

Encoder and DAQ Connections

What third party drive do I use to connect my umi-7764 to a phytron stepper motor (zss66)

Motion and Vector Space Question

What are the 4 analog inputs of my umi-7764 (on the analog input terminal block)

Does the breakpoint/trigger terminal block of my umi-7764 must be connected ?

What is the needed analog inputs to UMI 7764

How do i extend the bandwidth of my system

How to use an LVDT as an input to a UMI 7764

How to remove motion device from MAX?

flexmotion reading from board speed

How can I plot position,velocity and following error vs time?

can not read back error description in VB

implementation of Matlab neuro-fuzzy controller with Flexmotion-6C?

Is it possible to perfectly synchronize 7 axes using 2 motion controllers 7344?

I´m having problems with a simple synchronized move

3-D Models

How can I get a PWM signal of PXI-7344 by UMI?

High speed torque control with PCI-7342

Make sure motor is compatible with drive

how do i stop a motor from staring at full speed

Any examples that work with a PCI-6733?

control two different parameters at the same time

Stepper Motor Control, oscilator, with pauses

Error using communicate front panel in Value Motion

re-initialize the data during running the program

Master Encoder - Slave Axis Gearing (beginner's question)

FlexMotion 6.1 Read Buffer is buggy.

problem on control the bushless motors by motion asistant

configure ValueMotion board

I need help with motion control. I am programming in Visual Basic. I will need help with what parts I need to purchase from NI, along with help on the code.